Maxol Boiler Repairs London

Maxol Boiler Repair Help Centre

Maxol boiler faults, safe checks, and honest advice on repair versus replacement.

Jump to:
Quick Checks ·
Common Faults ·
Parts Situation ·
Repair or Replace

Maxol Boilers: What You Need to Know

Maxol is an obscure UK boiler brand that is no longer in production. If you have a Maxol boiler, it is almost certainly an older installation, likely 15-25+ years old.

The key challenge with Maxol boilers today is parts availability. Manufacturer support ended years ago, and while some generic components may still be sourceable, brand-specific parts (PCBs, gas valves, heat exchangers) are extremely difficult or impossible to find.

Our honest assessment: If your Maxol boiler has developed a fault, we will do our best to diagnose it and attempt a repair if parts are available. However, in many cases, replacement will be the more practical and cost-effective option.

Quick Checks Before You Call Anyone

These basic checks apply to most boilers and may resolve simple issues:

1. Check the pressure gauge (if fitted): If below 1 bar, you may need to top up. However, older boilers may have different system configurations. If you are unsure whether your system is sealed or open-vented, do not attempt to add pressure. More detail in our complete pressure guide.
2. Note any fault indication: Older boilers may show flashing lights, error codes, or simply fail to ignite. Write down or photograph whatever you see.
3. Check your fuse box: Boilers need electricity; a tripped breaker can look like a boiler failure.
4. Check thermostat and timer: Settings can change after power cuts or clock changes. Dead batteries in wireless controls can stop heat calls.
5. Check pilot light (if applicable): Some older boilers have a permanent pilot light. If it has gone out, you may be able to relight it following the manufacturer’s instructions (usually on a label inside the case). If you smell gas or the pilot will not stay lit, stop and call an engineer.
6. Reset once only: If there is a reset button, press it once and wait. If the boiler locks out again, stop and call an engineer.

Common Maxol Boiler Problems

Because Maxol boilers are older installations, they tend to experience age-related failures:

Ignition failure / no flame: The boiler attempts to light but cannot establish a stable flame. Common causes include worn ignition components (electrodes, leads), faulty gas valves, blocked burners, or (on condensing models) frozen condensate pipes in winter.

Pilot light problems: On older models with a standing pilot, the pilot may go out repeatedly or fail to stay lit. This can indicate a faulty thermocouple, blocked pilot jet, or gas supply issue.

Low pressure / pressure loss: On sealed systems, pressure dropping frequently usually indicates a leak somewhere in the system, or an expansion vessel / pressure relief valve issue.

No heating or hot water: Could be a diverter valve problem (on combis), pump failure, motorised valve issue, or a control/thermostat fault.

Strange noises: Banging, kettling, or gurgling can indicate sludge buildup, limescale, trapped air, or pump problems. Read our guide to boiler noises.

Leaking: Water from the boiler case, underneath, or from the pressure relief valve discharge pipe. This needs prompt attention.

Maxol: The Parts Situation

This is the critical issue with Maxol boilers:

• Generic parts (pumps, motorised valves, thermostats, some sensors): May still be available as these are often shared across brands
• Brand-specific parts (PCBs, gas valves, heat exchangers, burner assemblies): Extremely difficult or impossible to source

If your Maxol needs a brand-specific component, we will be honest with you: the part may not exist, or the cost and time to source it may exceed the value of the repair.

Repair or Replace?

For most Maxol boilers, this is the key question. Here is our honest guidance:

Repair may make sense if:

• The fault is simple (pilot light, thermostat, controls)
• The required part is generic and available
• The boiler has otherwise been reliable
• You need a short-term solution while planning replacement

Replacement is usually smarter if:

• The boiler needs a brand-specific part (PCB, gas valve, heat exchanger)
• You have had multiple breakdowns in the past 12 months
• The boiler is over 15-20 years old
• Efficiency has noticeably declined (higher bills, slower heating)
• You want reliability and the peace of mind of a warranty

A modern condensing boiler will be significantly more efficient than an older Maxol, potentially reducing your gas bills by 20-30% or more. It will also come with a manufacturer warranty and readily available parts for future servicing.

We give honest advice either way. Read more: Repair or replace? An engineer’s guide.

If you decide on a new boiler: New boiler installation.

What Happens When You Call Us

If you have a Maxol boiler and call us for a repair:

1. We will ask about the symptoms and any fault indications
2. We will be upfront about the likelihood of parts availability
3. If a visit makes sense, our engineer will diagnose the fault and assess repairability
4. We will give you honest options: repair (if viable), or replacement quotes
5. We will never pressure you into a decision

Boiler Servicing

If your Maxol boiler is still running well, annual servicing can help keep it that way for as long as possible. Servicing also gives us a chance to spot developing issues before they become breakdowns.

Book your boiler service.

Renting? Landlords: Check This

Tenants: Your landlord is usually responsible for boiler repairs. Contact them first and keep written records.

Landlords: If your rental property has a Maxol boiler, it is almost certainly approaching or beyond replacement age. Proactive replacement avoids emergency call-outs, tenant complaints, and potential compliance issues. Stay compliant with our Gas Safety Certificate (CP12) service. See our London landlord checklist.

London Wide Coverage

We diagnose and repair boilers across all London boroughs including North, South, East, West, and Central London.

For coverage and service areas, see our London coverage page.

We Repair All Major Boiler Brands

While Maxol parts are scarce, we repair and service all major brands with full parts support:

What We Need From You (To Diagnose Faster)

• Boiler model: Check the data plate (often inside the front panel or underneath)
• What is happening: No heating, no hot water, leaking, noises, fault lights
• Any fault indication: Flashing lights, error codes, or display messages
• Approximate age: When was it installed (if known)?
• Postcode: So we can route the closest engineer

Related Services and Guides